Descripción
Die Seat (10),
Para Llave Hidráulica Teda XQ140/12A,
XYQ12.Z-01.10 12A(60)
P/N: 12AZ-107.10,
0 o 2 pc/set.
Posición en el manual:
– 10.4 Mater tong head (Fig.43, Table 9)-8.
Tabla – Recomendación de Selección:
| Pipe string type | O.D mm (inch) | Die seat (stamp mark) | Dies (stamp mark on the backside) | ||
| Master tong | Backup tong | Master tong | Backup tong | ||
| Tubing | 60 (2 3/8″) | 12A(60) | 12A(70-73) | 12A(73-78) | 12A(73-78) |
| Tubing | 73 (2 7/8″) | 12A(70-73) | 12A(86-93) | 12A(73-78) | 12A(89-114) |
| Tubing | 89 (3 1/2″) | 12A(86-93) | 12A(102-107) | 12A(89-114) | 12A(89-114) |
| Tubing | 102 (4″) | 12A(102-107) | 12A(116-121) | 12A(89-114) | 12A(89-114) |
| Tubing | 114 (4 1/2″) | 12A(109-114) | 12A(128-132.5) | 12A(89-114) | 12A(121-156) |
| Tubing (EU) | 73 (2 7/8″) | 12A(70-73) | 12A(86-93) | 12A(73-78) | 12A(89-114) |
| Tubing (EU) | 89 (3 1/2″) | 12A(86-93) | 12A(109-114) | 12A(89-114) | 12A(89-114) |
| Tubing (EU) | 102 (4″) | 12A(102-107) | 12A(122-127) | 12A(89-114) | 12A(121-156) |
| Tubing (EU) | 114 (4 1/2″) | 12A(109-114) | 12A(128-132.5) | 12A(89-114) | 12A(121-156) |
| Casing | 114 (4 1/2″) | 12A(109-114) | 12A(128-132.5) | 12A(89-114) | 12A(121-156) |
| Casing | 127 (5″) | 12A(122-127) | 12A(138-143) | 12A(121-156) | 12A(121-156) |
| Casing | 140 (5 1/2″) | 12A(138-143) | 12AB(151-156) | 12A(121-156) | 12A(121-156) |
| Drilling pipe 2 7/8″ (male) | 105 (flat butt joint) | 12A(102-107) | 12A(102-107) | 12A(89-114) | 12A(89-114) |
| Drilling pipe 2 7/8″(male) | 108 (full-hole tool joint) | 12A(102-107) | 12A(102-107) | 12A(89-114) | 12A(89-114) |
| Drilling pipe 3 1/2″(female) | 108 (regular tool joint) | 12A(102-107) | 12A(102-107) | 12A(89-114) | 12A(89-114) |
| Drilling pipe 3 1/2″(female) | 118 (full-hole tool joint) | 12A(116-121) | 12A(116-121) | 12A(121-156) | 12A(121-156) |
| Drilling pipe 3 1/2″(male) | 121 (flat butt joint) | 12A(116-121) | 12A(116-121) | 12A(121-156) | 12A(121-156) |
|
Note: - Diameter refers to the outside diameter of tubing and casing, master tong clamps the pipe body, and backup tong clamps the coupling in making-up and breaking-out operation. - Both master tong and backup tong clamp the drilling pipe joint. The outside diameter of the drilling pipe refers to the outside diameter of the joint. - Use prolonged guide pole, select die seats and dies according to the actual diameter of pipe body to be clamped when backup tong clamps the body of the pipe. - It is not suitable for the pipe string with surface hardness degree≥340HB. - Special die seat and dies can be custom-made. |
|||||
Valoraciones
No hay valoraciones aún.